Detect electronic bite alarm 3+1 set
CARP ACADEMY
| Product number | 6320-003 |
| Quantity unit | pc |
A modern device with a refreshed design.
Waterproof push-button bite alarm with large indicator LEDs that remain visible from a distance. Features a 20-second bite afterglow and a built-in battery-voltage meter. Low power consumption. Range: 150–300 m, depending on terrain.
1. Insert a 9 V battery into each transmitter, observing the correct polarity.
2. Switching on/off and volume control: Press and hold the V button for 2 seconds. The device responds with three short beeps and flashing LEDs. Press it again to switch it off after a beep. Briefly pressing V lets you choose from four volume levels.
3. Tone: Press the T button to select one of four tones, confirmed by a beep and the indicator LED (6) flashing.
4. Sensitivity: Press the S button to select one of four sensitivity levels to suit waves and wind conditions. (Level 1 is the most sensitive.)
5. Memory LED / voltage indicator: The red, blue or green light stays on for 20 seconds after a bite. If the battery voltage drops below 5 V, the LED starts indicating low voltage.
1. Insert a 9 V battery into the receiver, observing the correct polarity.
2. Power switch: Slide the switch to the left to turn the device on. It confirms activation with two beeps and illuminated LEDs.
3. Volume control: Turn the V button to adjust the volume.
4. Tone setting: Turn the T button to change the tone.
5. Indicator lights / voltage warning: The bite alarms are factory-paired with the receiver, so when a bite is detected, the light matching the transmitter's assigned colour illuminates for 20 seconds. If the battery voltage falls below 5 V, all lights flash simultaneously.
6. Re-pairing: Press the concealed button on the back of the device; the red indicator LED turns on. Turn the magnetic wheel (line roller) of the bite alarm you want to pair, and the device confirms the transmitter with a beep. Press the concealed button again to pair additional alarms.
Maintenance: Always remove the batteries after use and store the set without batteries installed. The set is waterproof. If water nevertheless reaches the internal electronics and the alarm begins glowing or beeping continuously, remove the batteries and leave it to dry with the back open.
Waterproof push-button bite alarm with large indicator LEDs that remain visible from a distance. Features a 20-second bite afterglow and a built-in battery-voltage meter. Low power consumption. Range: 150–300 m, depending on terrain.
1. Insert a 9 V battery into each transmitter, observing the correct polarity.
2. Switching on/off and volume control: Press and hold the V button for 2 seconds. The device responds with three short beeps and flashing LEDs. Press it again to switch it off after a beep. Briefly pressing V lets you choose from four volume levels.
3. Tone: Press the T button to select one of four tones, confirmed by a beep and the indicator LED (6) flashing.
4. Sensitivity: Press the S button to select one of four sensitivity levels to suit waves and wind conditions. (Level 1 is the most sensitive.)
5. Memory LED / voltage indicator: The red, blue or green light stays on for 20 seconds after a bite. If the battery voltage drops below 5 V, the LED starts indicating low voltage.
1. Insert a 9 V battery into the receiver, observing the correct polarity.
2. Power switch: Slide the switch to the left to turn the device on. It confirms activation with two beeps and illuminated LEDs.
3. Volume control: Turn the V button to adjust the volume.
4. Tone setting: Turn the T button to change the tone.
5. Indicator lights / voltage warning: The bite alarms are factory-paired with the receiver, so when a bite is detected, the light matching the transmitter's assigned colour illuminates for 20 seconds. If the battery voltage falls below 5 V, all lights flash simultaneously.
6. Re-pairing: Press the concealed button on the back of the device; the red indicator LED turns on. Turn the magnetic wheel (line roller) of the bite alarm you want to pair, and the device confirms the transmitter with a beep. Press the concealed button again to pair additional alarms.
Maintenance: Always remove the batteries after use and store the set without batteries installed. The set is waterproof. If water nevertheless reaches the internal electronics and the alarm begins glowing or beeping continuously, remove the batteries and leave it to dry with the back open.
- Waterproof
- Volume (dB): 4
- Tone (dB): 4
- Sensitivity (dB): 4
- Power supply: 9 V
- Swinger connection
Customer Reviews
No review has been published yet...